Subscribe & save 15%On selected products. Cancel anytime.Explore subscriptions
Cart0
Simple Peptide customers: your account works here. Sign in with the same email and password, or with Google. Sign in
For laboratory research use onlyNot for human or animal consumption

How Peptide Molecular Weight Is Calculated

Clear information for responsible laboratory research.

Add each residue mass, add one water, then correct for amides (-0.98 Da), acetyl caps (+42.01 Da) and disulfides (-2.02 Da each).

Updated November 20, 2026 · Simple Life Science

For laboratory research use only. Not for human or animal use. This page covers chemistry, identity and paperwork only. It gives no use, preparation or administration instructions.

A peptide’s molecular weight is the sum of its residues plus one water, with corrections for anything at the ends or between side chains. Here is the method, with worked examples checked against PubChem.

The method

  • Write the sequence. Look up each residue mass (see the amino acid reference table).
  • Add them up.
  • Add one water (H2O) for a linear chain with a free N-terminal amine and a free C-terminal acid.
  • Apply corrections: C-terminal amide -0.98 Da, N-terminal acetyl +42.01 Da, each disulfide -2.02 Da, pyroglutamate start -17.03 Da (from Gln).
  • Use average masses for weighing and molarity; use monoisotopic masses to compare with high-resolution mass spec.

Worked example 1: KPV (Lys-Pro-Val)

Part Monoisotopic (Da) Average (g/mol)
Lys residue 128.09496 128.175
Pro residue 97.05276 97.117
Val residue 99.06841 99.133
Water 18.01056 18.015
Total 342.2267 342.44

PubChem lists KPV at 342.43 g/mol and 342.2267 Da. The sum matches. See the KPV molecular data page.

Worked example 2: oxytocin (amide end + disulfide)

Sequence Cys-Tyr-Ile-Gln-Asn-Cys-Pro-Leu-Gly-NH2 with a Cys1-Cys6 bridge. Sum of residues + water, then -0.98 Da for the amide and -2.02 Da for the bridge, gives formula C43H66N12O12S2, the same as PubChem, monoisotopic mass 1006.4365 Da and average 1007.2 g/mol. See the oxytocin molecular data page.

Where calculators go wrong

  • Non-standard residues (Aib, naphthylalanine, adamantane-based residues) are missing from most calculators; use the full formula instead. Examples: Ipamorelin, P21 (P021), GHRP-2 (Pralmorelin).
  • Forgetting an end group: an amide or acetyl cap shifts the mass enough to fail an identity check.
  • Using average mass to read a high-resolution spectrum, or monoisotopic mass to weigh powder.
  • Ignoring salt form: the weight you put on the balance includes counter-ions. See net peptide content.

The peptide property calculator does these steps for standard sequences and shows charge, pI and extinction coefficient too.

Related pages

Common questions

How do you calculate the molecular weight of a peptide?

Add the residue masses of each amino acid, add one water, then correct for end groups and disulfides.

Why add one water?

Each peptide bond loses one water. A chain of n residues has n-1 bonds, so the residue sum is one water short of the full molecule.

Which mass should I use for weighing?

Average molecular weight, adjusted for net peptide content if you need the exact peptide amount.

Research use only. Not for human or animal use. Simple Life Science is operated by Melex Technologies Inc., 6586 W Atlantic Ave Ste #1112, Delray Beach, FL 33446.

¿Prefieres español? Ver en español